A rubber track that has come off, or worn through to the cords, stops a mini digger where it stands. This guide covers how to read the size on the track, how to release the tension safely, how to walk the track off and on again, and when the job belongs with a fitter.
Release the tension at the track adjuster grease valve, lift that side of the machine with the boom and blade, feed the track over the sprocket first and the idler last, then re-tension with a grease gun to the sag figure in your operator's manual. A track in good condition can be refitted on site. A track with exposed cords, cracked lugs or missing tread blocks needs replacing, and the cause of the detracking needs finding, or it will come off again.
Refit it or replace it?
Decide this before anything is lifted. A track that has walked off the idler with the tread, the drive lugs and the guide lugs intact goes back on. A track with the steel cords showing through the rubber, split or missing drive lugs, or tread blocks torn away is at the end of its life, and refitting it only buys a few hours.
Either way, the track did not come off on its own. Lost tension from a failed track adjuster, worn sprockets, worn rollers or idlers, the wrong pitch, a packed undercarriage and side hill working are the documented causes, covered in our guide to why digger tracks come off. Fix the cause as well as the symptom.
How to read the size on a rubber track

Rubber tracks are sized by three numbers: the width of the track, the pitch, which is the distance between the centres of two drive lugs, and the number of links, which is the number of drive lugs around the track. A size such as 300 x 53 x 80 means a 300mm wide track with a 53mm pitch and 80 links. The size is usually moulded into the inside face of the track, so look there first.
Width is the easy one. Pitch is where mistakes happen, because two tracks of the same width can be built on different pitches, and a track on the wrong pitch will not sit correctly on the sprocket. Our guide to long pitch and short pitch rubber tracks explains the difference and why it matters. If the marking has worn away, send us the machine make, model and serial number and we will confirm the size.
The TerraTrack range is stocked in widths from 180mm to 800mm, with non-marking tracks for specialist applications. Rubber tracks are usually fitted to machines up to 8 tonnes. Above that, most machines run steel, which is covered in our guide to rubber tracks or steel tracks.
Before you start
Park the machine on firm, level ground with room to work on the side that needs attention. Have the operator's manual to hand, because the lifting method and the tension setting are specific to the machine. You will need a grease gun, a long bar, timber to block the raised track frame, and a second person. Stop the engine before anyone works under or beside a raised track, and never rely on the hydraulics alone to hold the machine up.
Step 1: release the track tension

The track adjuster fits in the undercarriage frame between a bulkhead and the idler, and its function is to keep the track correctly tensioned. It has three integral parts: a tensioning piston, which is a grease-filled ram, a spring pack that absorbs impact, and a fork-shaped yoke that bolts to the idler. Tension is set by pumping grease in through a nipple and released by unscrewing the grease valve.
Remove the access cover on the track frame to reach the valve. Unscrew the grease check valve carefully and let all the grease drain to fully relieve the cylinder pressure. The grease is under high pressure, so turn the valve slowly, keep your face and hands clear of the port, and do not remove the valve completely. As the grease comes out, the idler moves back and the track slackens. If no grease comes out and the track does not slacken, the adjuster may have failed, and our guide to track adjusters covers the failure modes.
The full procedure for checking and adjusting tension, with the safety points in order, is in our guide to excavator track tension.
Step 2: lift the machine and walk the track off
With the tension released, raise the side of the machine that needs the track. On a mini digger this is normally done with the boom and the dozer blade, following the method in the operator's manual: slew the upper structure across the machine, push the bucket down to lift that track clear of the ground, and use the blade to steady it. Once the track frame is clear, block it with timber so it cannot drop.
Push the slack to the idler end and use the bar to lever the track off the idler. With the track clear of the idler, rotate that side slowly in short movements so the track feeds off the sprocket and the rollers. Even a small rubber track is heavy and awkward, so keep feet clear and have the second person guiding it.
Step 3: fit the new track or refit the old one
Check the new track against the old one for width, pitch and link count before it goes anywhere near the machine. If the tread pattern is directional, the track will carry a direction marking, and it must face the way the manufacturer specifies. Lay the track flat beside the undercarriage, guide lugs inward, in line with the rollers.
Fit the sprocket end first. Feed the track over the sprocket teeth so the drive lugs sit between the teeth, then along the top of the track frame and under the rollers, so the guide lugs run between the rollers. The idler goes on last: with the slack gathered at the front, lever the track over the idler with the bar, rotating the sprocket in short movements to take up the length. Check all the way round that the guide lugs sit between the rollers and that nothing is trapped or twisted.

TerraTrack
Quality rubber tracks in widths from 180mm to 800mm, including non-marking options, backed by a full 24-month warranty.

TerraTrack Plus
Interlocking steel links engineered to resist detracking, with anti-vibration links for smoother roller travel and lower noise.

Order by 4:30pm
Order by 4:30pm for next working day UK delivery from stock, so the machine is back on its tracks the following day.
Step 4: re-tension and check
Lower the machine to the ground and pump grease in through the nipple until the track sag matches the figure in the operator's manual, measured the way the manual describes. A track that is too slack will come off again. A track that is too tight loads the idler, the rollers, the adjuster and the final drive. Refit the access cover, run the machine forwards and backwards slowly on level ground, then re-check the sag on both sides. On a new track, check the tension again after the first few hours of work.
Refitting a thrown track is within reach of a competent operator with the right equipment. Three situations are not. If the machine cannot be lifted and blocked safely where it stands, if the track adjuster has failed and the track will not slacken or will not hold tension, or if the detracking keeps happening, stop and book a fitter.
Utilising a nationwide network of approved plant fitters, our fitters will come to you anywhere within the UK through our onsite fitting service, and our workshop services cover the jobs that need a bay rather than a yard. Once the machine is moving again, a free track inspection measures the sprockets, rollers, idlers and adjusters against new dimensions and finds the component that threw the track.
What to do with the old track
Astrak runs a sustainable, UK-wide rubber track recycling programme. The service is fully compliant and includes all relevant waste transfer documentation, including certified waste transfer notes, and transportation. Ask about it when you order the replacement, so the old tracks leave site when the new ones arrive.
Frequently asked questions
How do you put a track back on a mini digger?
Release the track tension by carefully unscrewing the grease valve on the track adjuster, lift that side of the machine clear of the ground with the boom and blade, feed the track over the sprocket first and the idler last, then pump grease back in through the nipple until the sag matches the figure in the operator's manual. If the track is damaged, or you do not have the equipment to lift the machine safely, book a fitter instead.
How do I know what size rubber track I need?
Rubber tracks are sized by width, pitch and number of links, in millimetres, for example 300 x 53 x 80. The size is usually moulded into the inside of the track. If it has worn away, send us the machine make, model and serial number and we will confirm the size.
Can I change rubber tracks myself?
A thrown track in good condition can be refitted on site with a grease gun, a bar and a safe way to lift and block the machine. Fitting a new track is the same job with a heavier lift. Follow the operator's manual, and if you are unsure, our nationwide network of approved plant fitters will come to you anywhere within the UK.
Why does my track keep coming off after I refit it?
Because the cause has not been fixed. Lost tension from a failed track adjuster, worn sprockets, worn rollers or idlers, or the wrong pitch of track will throw it again. A free track inspection measures each component against new dimensions and identifies which one is responsible.
What should I do with the old rubber tracks?
Astrak runs a sustainable, UK-wide rubber track recycling programme. The service is fully compliant and includes all relevant waste transfer documentation, including certified waste transfer notes, and transportation.
Need a replacement rubber track?
Send us the machine make and model, or the size moulded into the track, and we will confirm the right TerraTrack and current availability. Order by 4:30pm for next working day UK delivery.
Astrak Group develops and manufactures products intended to be compatible with machinery and equipment from various manufacturers. Unless indicated otherwise, Astrak Group has no relationship, commercial or otherwise, with the owners of the trademarks.
Need help finding the right part?
Our team is here to help with expert advice and support for your order.
