DuraTrack Dozer Undercarriage
Dozer Undercarriage Parts
DuraTrack dozer undercarriage comprises sealed and lubricated (SALT) track chains, track groups, single grouser shoes, sprocket segments, rollers, idlers, track adjusters and hardware, manufactured in OEM production facilities to rigorous OEM standards. Every component is tested and inspected to ensure correct fitment, durability and consistent quality.
The range covers all major makes and models of crawler dozer and tracked loader, including CAT, Komatsu and Liebherr. Parts are supplied individually, as half kits and full kits, or as a complete undercarriage, with custom track groups assembled in our Houston workshop.
- Held in US stock, same-day shipping on a 4:00pm CT cut-off
- Oil filled SALT chains with bushing life up to 50% longer than greased and sealed chains
- Conversion kits for Cat SystemOne and Komatsu PLUS undercarriages
- Custom dozer track groups assembled in our Houston workshop
- Manufactured to OEM specification in ISO 9001 approved facilities
Shipping & Warranty
Get a QuoteDozer Undercarriage Parts by Component
Nine wearing components, each manufactured to OEM specification. Select a component to browse parts by machine make and model.
Dozer Track Chains
Sealed and lubricated (SALT)Oil filled to reduce friction between pin and bushing, extending internal bushing life by up to 50% compared to greased and sealed chains. Boron steel rails hardened to 48-56RC up to 13mm deep; pins and bushes to 55-60RC.
Dozer track chainsBrowse dozer track chains by machine
Track Groups
SALT chain and shoes, assembled to orderFully assembled dozer track groups with the chain and single grouser shoe configuration to suit the machine and application. Assembled to order in our Houston workshop and shipped ready to fit.
Track groups
Track Shoes
560mm to 915mm single grouserSingle grouser dozer shoes in all standard widths from 22in (560mm) to 36in (915mm), with heavy-duty baseplates to increase service life. Boron steel, through hardened and stress relieved.
Track shoes
Sprocket Segments
Three or five tooth sectionsForged and through hardened for extended wear life, with tooth profiles induction hardened to over 50RC. Segments are replaced individually without removing the track.
Sprockets and segments
Bottom Rollers
Single and double flangeTransfer machine weight through the undercarriage to the ground. Forged roller shells, heat treated, on hardened forged alloy or rolled carbon steel shafts, with heavy-duty seals.
Track rollers
Carrier Rollers
Single flange, double flange and shaft typeGuide the track over the undercarriage frame. Reinforced flanges and heavy-duty sealing systems extend wear life.
Carrier rollers
Idlers
Front and rear, complete cast assembliesCast idler assemblies produced to OEM specification, complete with heavy-duty seal groups, shafts and brackets.
Idlers
Track Adjusters
Recoil spring assembliesOEM specification track adjuster assemblies: tensioning piston, spring pack and yoke, maintaining correct track tension under dozing loads.
Track adjusters
Hardware
Grade 12.9 and 10.9, metric and imperialTrack bolts, segment bolts and split master bolts to Grade 12.9; sprocket and roller bolts to Grade 10.9. All forged from alloy steel and heat treated to OEM specification.
Undercarriage hardwareSystemOne and PLUS Conversion Kits
Proprietary undercarriage systems such as Cat SystemOne and Komatsu PLUS can be expensive to maintain compared to a DuraTrack SALT undercarriage. A DuraTrack conversion kit moves the machine onto the industry-standard SALT configuration, so every future replacement part comes from stock.
The kit contains every part needed for the conversion, with comprehensive step-by-step instructions for customers carrying out the work themselves. Alternatively, our Houston workshop carries out the conversion for you.
- Every conversion kit component manufactured to OEM specification
- Conversions carried out in our Houston workshop
- Reduced whole-life repair costs, with replacement parts held in US stock
Dozer Undercarriage Wear and Measurement
Dozer undercarriage wears as one system. A worn sprocket segment shortens the life of a new chain, and one new roller among worn ones wears faster than the set it replaced. Four measurements determine most replacements: chain stretch, rail height, grouser height, and roller and idler tread wear.
- Chain stretch. Measured across four or five pin centres against the new specification. On a 50 link chain, 1mm of pin wear plus 1mm of bush wear adds around 100mm to the overall length.
- Sprocket segments. Compared against an unused segment of the same type. Sharp or hooked teeth let the chain jump, which shock loads the final drive. Wear increases in reverse and in higher gears.
- Rollers. Change all bottom rollers together. One new roller among worn ones stands proud and carries more than its share of the load.
- Shoe width. Use the narrowest shoe that still gives adequate flotation. Excess width accelerates bush, sprocket, link and roller wear and loosens hardware.
Application sets where the wear falls. Dozing and push loading load the front of the undercarriage, ripping and drawbar work load the rear, and side hill work loads the downhill side. Avoid track slip, unnecessary reversing, non-productive high speed travel and always turning in one direction.
What we need to identify your dozer undercarriage
How to measure grouser height
Stock, Quality, Delivery and Warranty
Large Stock Availability
The full DuraTrack dozer range held in US stock to suit all major makes and models of crawler dozer, maximizing machine uptime.
Quality Approved
Manufactured to OEM specification in ISO 9001 approved facilities.
Same-Day Shipping
Order by 4:00pm CT and stocked parts ship the same day from US stock.
Warranty Backed
Three years or 4,000 hours on DuraTrack SALT dozer chains, whichever comes first. Minimum 12 months on other DuraTrack components.
Dozer Undercarriage Services
Track group assembly, kits and conversions from our Houston workshop.
Measure Before You Buy
Measure each dozer undercarriage component against new dimensions before you buy, so parts are changed once, together, rather than twice. Our team will tell you what to measure.
Talk to the teamHalf Kits and Full Kits
A half kit is the track groups, sprocket segments and segment hardware. A full kit adds the idlers, carrier rollers and bottom rollers with their hardware, so the whole undercarriage wears from the same starting point.
Get a kit quoteHouston Workshop and Conversions
Custom dozer track groups assembled to order on 4 track presses, SystemOne™ and Komatsu PLUS conversions, track repairs and repair sections. Same-day pickup and local delivery are available on many orders throughout greater Houston.
Workshop servicesDozer Undercarriage Questions, Answered
What is a SALT track chain?
Should I replace the whole dozer undercarriage or just the worn part?
What is in a half kit and a full kit?
Can you convert a Cat SystemOne or Komatsu PLUS undercarriage?
What warranty comes with dozer undercarriage parts?
Which dozer makes do you cover?
Do you assemble dozer track groups in the US?
How fast can you ship dozer undercarriage parts in the US?
Get a Quote for Dozer Undercarriage Parts
Send the machine make, model and serial number, with the roller count, link count and shoe width if you have them, and whether the machine is on SystemOne or PLUS. We check the parts against our product reference guide, price them, and ship from US stock.
Speak to the Team
Technical advice on identifying dozer undercarriage parts comes at no additional cost.
Call Us